CLW GROUP's Dongfeng chicken transport truck exported to Tanzania The body is made of glass steel plate inside and outside, 8cm insulation board in the middle, aluminum checkered plate, 2 shutters on the front panel of the body, 3 shutters on both sides of the body (with small doors can be Open), two electronic fans (with sliding doors) on the back door of the box, two skylights on the top of the box, three electronic fans on each side of the skylight, two ventilation ducts on the bottom plate, and two outlets on each side of the box At the door, Hanxue L-Z20 refrigeration unit is installed,truck and winch santa ana.
2014: CLW Group won the ""Dongfeng Engineering Vehicle Outstanding Contribution Award"" Dongfeng Company stated that its achievements in 2014 are inseparable from the support of outstanding talents and partners At the annual meeting, awards were given to partners who obtained outstanding achievements in 2014 Chengli Company was awarded the ""2014 Outstanding Partner of Dongfeng Company"" , Dongfeng Engineering Vehicle Division issued the ""2014 Dongfeng Engineering Vehicle Outstanding Contribution Award"" It is believed that with the good cooperation foundation and policy support, Chengli Company and Dongfeng Company will have a better future for cooperation in special vehicles,truck and winch santa ana.
What should I do if there is neither a float to replace nor a welding repair tool when the flatbed transporter is driving? The CLW Group after-sales master said that the float can be removed first, and the broken part of the float should be placed in hot water (water temperature 95℃~98℃). The gasoline in the float will evaporate from the leak due to heat, and then the float will be removed from the heat. Take it out of the water and place it in the air to cool it naturally. Finally, it can be heated with battery sealant, epoxy resin glue, rubber (or plastic cloth) ignited and melted and coated on the leak to seal.
The ambulance with the Ford chassis produced by CLW Group is a load-bearing high-rigidity car body, which is made of high-strength galvanized sheet, cast like a high-rigidity chassis, and has high safety performance. The car body is equipped with a single-door and double-door structure to facilitate personnel Access and patient transfer. Equipped with professional rescue systems such as automatic stretchers, scoop stretchers, and suspended infusion bottle holders, it is simple to operate and easy to transport. At the same time, it is made of aluminum alloy material, which can assist the stretcher to get on the car, and guide and fix it to protect the floor.
The sludge truck produced by CLW Group adopts a solid chassis, strong engine power and a comfortable driving experience. It mainly produces 5-6 square tank sludge trucks, 8-10 square tank sludge trucks, and 12 square tank sludge trucks. Mud truck, 16 square tank sludge truck, 18 square tank sludge truck, 20 square tank sludge truck. The tank sludge trucks produced by our company are of high quality, and the service is guaranteed, with 7*24 support before, during and after sales.
Many customers inquired about the routine maintenance of road sweeper engines. The editor of CLW Group organizes as follows: 1. Lubrication: including adequate lubrication of all parts of the machine and timely replacement and supplementation. 2. Cleaning: Including the care of the appearance of the parts and the cleaning of the inside and outside of each assembly and parts.3. Inspection: including inspection of the appearance, working conditions and tightness of connecting bolts of each assembly and machine parts of the road sweeper. 4. Fastening: The focus of work is to fasten and replace the connection parts of various parts that are heavily loaded and frequently changed, as well as the necessary fastening and replacement of the connecting bolts. 5. Adjustment: According to technical requirements, restore the normal clearance and working performance of the assembly, parts and instruments.
Truck and winch santa ana,CLW group brought everyone a 3.8-meter refrigerated truck chassis evaluation this time. This car is equipped with a national six Dongan dual-fuel 105 horsepower engine, 1.6L displacement, can use gasoline fuel or natural gas fuel, matching Dongan five-speed gearbox. A 20L black iron fuel tank is installed on the right rear of the vehicle body. There are 80 cubic meters of natural gas storage tanks installed on the left and right sides of the vehicle body, and the storage capacity of the vehicle is 160 cubic meters. The bottom adopts a 1028 rear axle, a 140*4 girder, and the rear two-wheeled 185/65R15 tires, which have strong bearing capacity. A 24V animal battery is installed behind the cab for easy ignition. For this 3.8-meter refrigerated truck, its service life must be longer than that of single gasoline and single diesel vehicles. Because natural gas has no emissions problems, it will save a lot of later troubles.
