CLW GROUP has produced a variety of dangerous goods and chemical transport vehicles before. The medium stored by the customer this time is: ammonia solution, sodium hydroxide solution, sulfuric acid and other corrosive chemical solutions packed in independent containers (bottles), which will affect the car body The tightness and safety of the product have high requirements. According to customer needs, our company chooses high-quality materials that are resistant to acid and alkali to make the body. It is produced in strict accordance with the process flow and the highest level of quality inspection is used. Do not let customers feel at ease and rest assured during use.
The editor of CLW Group will give you a comprehensive understanding of the reasons for the difficulty of turning the water ring vacuum pump of the vacuum sewage truck 1 The gap between the positioning bearings at both ends of the pump is not adjusted properly, that is, when the thickness of the gap adjustment spacer ring is less than the original thickness, when the back cap is locked, the two rows of inner and outer rings are squeezed by unconventional forces, causing the bearings to rotate Difficult or unable to turn 2 The bearing inner ring is not installed in place 3 The gap between the impeller and the two ends of the pump is not adjusted properly The adjustment method is to add or subtract shims between the bearing seat and the positioning surface of the bracket where the bearing seat is installed 4 After the sealing surfaces of the static and dynamic rings of the mechanical seal are broken, they will jam each other,How about CLW Special Automobile Co.Ltd..
What safety issues should be paid attention to for dangerous goods transport vehicles such as oil tankers and chemical vehicles? CLW Group technicians said: First of all, the safety performance of the vehicle container must be checked one by one before leaving the vehicle, such as whether the safety devices such as pressure gauges, valves, and emergency shut-off valves are intact, and faults should be eliminated in time Secondly, when the container is filled with liquid, the reserve volume should not be less than 5% of the total volume of the expansion margin Finally, you must be diligent in inspections while driving, check every two hours for leaks such as overflow on the lid of the barrel, and immediately report to the relevant department if any problems that cannot be handled are found,How about CLW Special Automobile Co.Ltd..
The main transport medium of the transport truck provided by CLW GROUP to Jiapurui Company is three types of hazardous chemicals, including paint and coating, etc. The body is made of iron corrugated board, there is a horizontal ring for fixing the goods, and the bottom plate is covered with anti-static rubber; To ensure the safety problems caused by dangerous chemicals, the car is also equipped with a special on-board smoke alarm and rear door anti-theft device, static belt, fire extinguisher, and fire cover. Reflective markings and warning signs of the whole vehicle national standard. The main transportation medium is three types of hazardous chemicals, including paint, etc. There are double-open side doors in the middle of the compartment.
Summer is approaching. Recently, many friends have started to buy refrigerated trucks. Today, CLW group will give you an evaluation of the cab of the JAC Junling V6 4.015 refrigerated truck! This car uses the JAC Junling V6 series single-row cab. The appearance adopts an internationally popular design, which highlights the stable, modern and fashionable elements, and shows high-end taste. The inner space is more comfortable, the cab is taller, and the height is 50mm higher than the traditional light truck cab, which is not easy to fatigue; the A-pillar angle is optimized to ensure the space while taking into account the streamlined shape of the vehicle and reduce the wind resistance; the fully-wrapped aviation seat makes adjustment more flexible , High ride comfort.
How about CLW Special Automobile Co.Ltd.,The watering truck models produced by our company adopt assembly line assembly. Each component of the whole vehicle adopts assembly design, which is convenient for disassembly and maintenance of each component. It is also convenient for the maintenance and replacement of the pump and main road suspended at the bottom of the vehicle, which can realize unified and standardized production of products. . And the parts of mature stereotyped products can be prepared in advance, thus shortening the production cycle of the order car. At the same time, the parts assembled by the assembly line are painted first and then assembled, so that the paint can reach 360 degrees without dead angles, and the painting quality is better.
The production of all tank cars of CLW Group follows strict processing and production procedures, and quality comes from ingenuity. In the tank body produced by CLW, an arc-shaped partition is placed every 1.5 meters inside the tank body, which has the effect of anti-wave and anti-vibration. Taking into account the safety issue, in order to avoid the situation of poor car effect and steering wheel steering failure due to liquid collision under full load. Therefore, for every tank vehicle, CLW will use this process. Ensuring safety is a priority for CLW.
