CLW GROUP reports of good news frequently First, Henan Highway Maintenance Bureau purchased 10 National Five Furika Road Sweepers from our company and delivered them smoothly Then, Guizhou County Government purchased 20 Futian Yuling 3-square hook-arm garbage trucks and 200 3-square hook-arm garbage trucks from our company The dustbin was shipped smoothly Do you think that September is over? Of course not, the Xinjiang Environmental Sanitation Bureau purchased 20 Dongfeng Duolika compact garbage trucks and 12 Dongfeng Duolika bucket garbage trucks from our company and delivered them smoothly,what sound does a ambulance siren make.
The collection and transportation method of CLW Group docking garbage trucks is the garbage transfer method widely used in garbage compression stations in China. We will show you how to deal with when the hydraulic mechanism of docking garbage trucks does not work properly. You can check this according to the following steps: 1. Whether the amount of oil in the hydraulic oil tank is sufficient; if it is insufficient, add hydraulic oil; 2. Observe whether the oil intake pipe from the oil tank to the oil pump is deflated due to aging. If this phenomenon occurs, the oil inlet pipe should be replaced; 3. Check whether the gear oil pump fails. Install the pressure gauge, turn the pressure-regulating bolts, and observe whether the gauge reaches the specified value.
Now that it is understood that the valve water is frozen and cracked because of the water stored in it, how can I clean the water? 1 Open the 45-80 degree self-flow valve to ensure that the remaining water in the tank is drained 2 Open all pipe manual ball valves (including all outlet valves and return valves) 3 Turn on all the front spray, rear spray and side spray electronic control switches on the center console of the cab; turn on all the pipelines and the drain nozzle at the bottom of the pump until all remaining water in the tank and pipelines is released This is the method summarized by CLW Group for you,what sound does a ambulance siren make.
In order not to affect the customer's construction period, the workers of CLW GROUP worked overtime and worked non-stop to make the sprinklers. At the same time, they have high standards and strict requirements in the production process of all links, and the excellence is not sloppy at all. After four days of hard work by the workers and masters, the 15-cubic Dongfeng Tianjin water truck was finally built and presented to the customers perfectly. So when the customer saw this high-quality sprinkler truck, they couldn't help giving a thumbs up to the staff!
What sound does a ambulance siren make,The second part of the comprehensive evaluation of CLW group evaluation of Dongfeng washing and sweeping vehicles. The upper box is made of stainless steel, and the side panels of the box are of corrugated board structure, which effectively increases the rigidity and strength of the entire box. The red scrubbing brush is installed under the box and made of tetrafluoroethylene. It is rotated by the motor to sweep the stubborn garbage on the road to the middle of the vehicle, so that the suction cup can suck garbage and sewage into the garbage bin. The suction cup with yellow casters is located behind the sweeping brush. The suction cup has a built-in high-pressure side spray rod. The stubborn dirt is cleaned up by washing and suction. The height of the casters can be adjusted to assist the vacuum truck to clean up garbage.
"CLW Group has introduced the most advanced domestic production technology for refrigerated trucks and has invested heavily in the purchase of the most advanced 16-meter hydraulic large-scale composite panel production line in the country to manufacture a new generation of refrigerated and insulated trucks. The inner and outer walls of the refrigerated trucks produced are made of high-quality wear-resistant FRP , Stainless steel or color steel plate; 8cm thick imported polyurethane foam insulation board is selected as the intermediate insulation material; high-quality aluminum alloy profiles are selected around the car body; the bottom plate is made of wear-resistant FRP, non-slip 304 stainless steel or aluminum alloy checkered board.
Large-scale pre-bending plate rolling machine owned by CLW Group: hydraulic computer control, maximum plate thickness 40mm. The advantage lies in its hydraulic drive, high transmission efficiency, and small size; it uses lubrication-free bearings; the diameter of the reel is small, only 1.1 times the diameter of the upper roller; it automatically matches the speed of the upper and lower rollers; it is controlled by CNC machine tools and can be automatically generated The program can be modified and stored to realize network control; it can realize CAD/CAM and display in real time in the form of three-dimensional animation.
