CLW GROUP recently successfully delivered a 15-square water truck to the customer The customer spoke highly of the car's interior refinement, luxury, comfort, engine sound, and vehicle assembly The full set of watering truck pipes for 15 square watering trucks are made of seamless steel pipes, and the exterior is painted with zinc plating, which is not only beautiful, but also can prevent rust All watering truck system valves are pneumatically controlled, and the pneumatic switch is integrated in the cab for operation Save labor cost and reduce labor intensity of operators,which ambulance company to work for emt.
The most important thing for the normal use of the LED publicity car produced by CLW Group is the maintenance of the screen. Under the normal sunny environment, the screen clarity of the LED publicity car is very good, but when it reaches the rainy weather, the display will be a little bit poor. Cleared. Therefore, when it rains, we should try to reduce the intensity of the publicity vehicle outside, and let it wait until the rain has completely stopped before going out for promotion. When there are signs that the display screen is starting to blur, if it is not caused by circuit system problems, but the simple display is not clear, you can drive the promotional car to a place where the sun is slightly softer when the weather is good to allow accumulation The mist and water vapor in the display evaporate clean.
What is the manifestation of the leak of the carburetor float of the flatbed truck? The CLW Group after-sales master explained based on past experience: the carburetor will cause the oil level in the float chamber to rise due to the leakage of the float, and the mixture will be too thick, which will cause the engine to run unsteadily and become stuffy Black smoke, this is a relatively common fault when the float leaks It can be repaired by welding or replacing the float,which ambulance company to work for emt.
CLW GROUP's Dongfeng chicken transport truck exported to Tanzania. The body is made of glass steel plate inside and outside, 8cm insulation board in the middle, aluminum checkered plate, 2 shutters on the front panel of the body, 3 shutters on both sides of the body (with small doors can be Open), two electronic fans (with sliding doors) on the back door of the box, two skylights on the top of the box, three electronic fans on each side of the skylight, two ventilation ducts on the bottom plate, and two outlets on each side of the box At the door, Hanxue L-Z20 refrigeration unit is installed.
Which ambulance company to work for emt,CLW group introduced the chassis evaluation of Dongfeng 16m folding boom aerial operating vehicle. The car's power source is equipped with a 126-horsepower engine of the Yunnei Dewei D20 series. The maximum output power is 93kW, and the maximum torque is 350N.m. The engine is in the form of an electronically controlled common rail system, matched with a Wanliyang 5-speed gearbox, which is full of power. In the protective rail on the left side of the car body, there is a urea tank, next to the fuel tank and gas storage tank, the layout is compact and space saving. A fuel filter is installed behind the cab on the right side of the vehicle body, which can be pumped twice when it fails to catch fire; the two 24V batteries in the rear protective fence are covered with dust covers to provide a certain degree of protection.
The refrigerated trucks produced by CLW Group are manufactured using a 1200-ton hydraulic heating and curing equipment integrated production line, and the insulation technology of the car body reaches the national A-level standard. 1. Fully sealed resin adhesive bonded polyurethane foam board is cured by high pressure heating, and the thickness of the compartment board is 8cm; 2. The inner and outer fabrics of the compartment board are 2.5mm thick new glass fiber reinforced plastic; 3. Adhesion accessories are glass fiber silk cloth; 4. Plate Structural polyurethane foam insulation material; 5. Fully sealed resin adhesive bonding; 6. Pre-embedded solid wood car body reinforcement; 7. The car body frame is supported by anti-rust treatment channel steel; 8. Aluminum alloy edging/stainless steel corners; 9 , Install LED lights inside the car body; 10. Install LED width lights on the car body; 11, install LED side lights on the car body above 3.5 meters.
CLW Group obtained the AAA Credit Enterprise Certificate issued by Industrial and Commercial Bank of China. AAA grade Excellent credit The company has a high degree of credit and low debt risk. Such enterprises have excellent credit records, good operating conditions, strong profitability, and broad development prospects. Uncertainties have minimal impact on their operations and development. The score is 90 points or more, and the asset-liability ratio, interest repayment rate and maturity credit repayment rate index scores are all full marks.
