The staff of CLW GROUP welcomed Mr Wang from Chongqing who came to pick up the car Mr Wang ordered 5 sets of 124m miscellaneous dangerous goods semi-trailers from our company this time The vehicle is a dangerous goods transport vehicle with a closed top and cannot be opened; when the side door type and location are selected, the internal width of the vehicle body is 2360 (mm) This vehicle is specially used to transport containers with independent containers (bottles, bags, barrels) Copper waste, nickel-containing waste, lead-containing waste, chromium-containing waste, waste batteries, zinc-containing waste, waste mineral oil,who works in a ambulance.
What to do if the surface of the sprinkler is rusty? The editor of CLW Group recommends the following: There are two types of rust on the surface of the sprinkler. One is the rust on the paint surface. Normally, such rust cannot be dealt with by yourself. You must get an outside car specializing in sandpaper to help you remove it. Rust and then touch up the paint. If the rust is not very serious, you can first use very fine water sandpaper dipped in water to lightly polish the rust spots, but avoid random grinding without direction, and polish in the same direction. After it is completely wiped off, apply a layer of primer.
In the process of tank truck transportation, static electricity is an "invisible fire", which is most likely to cause unexpected and dangerous accidents Then, how to prevent static electricity from harm? The engineering staff of CLW Group, a professional manufacturer of tank trucks, remind you to pay attention to the following aspects: 1 The amount of fuel in the tank of the tank truck must be appropriate; 2 When changing the fuel tank, the original fuel must be drained; 3 Keep the tank of the tank truck clean 4, 4 Ensure that the other accessories of the tank truck are in good condition; 5 Connect the static wire; 6, 6, ensure that the anti-static facilities on the tank truck are in good condition,who works in a ambulance.
Who works in a ambulance,This time, CLW GROUP used Dongfeng 498 engine, 5-speed gearbox, 7.00-16 tires for the Dongfeng Xiaodolika compression garbage truck for Baobei Baojing customer production plant. Flip, with sewage tank, with manual hydraulic operating system, manual electric dual control, side-mounted controller, hydraulic pressure is electromagnetic control, the box body is arc channel steel frame. The new arc-shaped design box body refuses to weld and crack. The box body is stronger and has a longer service life.
Among the special vehicles, there is a category of vehicles called dangerous goods transport vehicles. However, there are also many types of dangerous goods transport vehicles, which are classified according to the type of goods transported. Let's take a look at the chassis configuration of this Dongfeng 3m flammable gas van with CLW group. The chassis of the car is equipped with Dongfeng Microcard Tuyi T5 series chassis, the height of the car is controlled within 2.1 meters, and there is no pressure to travel in the city. The engine uses Wuling Liuji gasoline engine code-named LJ4A15Q6, 112 horsepower, maximum torque of 147nm, five-speed gearbox. The front and rear axles adopt leaf spring suspension, and the 3 tons rear axle reinforced manganese steel 75mm wide frame. The rear axle is equipped with rear twin tires to further strengthen the loading performance.
The emergency start control device for ambulances produced by CLW Group. When the main battery cannot start normally when the main battery is lower than 12V, press and hold the emergency start switch to start the car quickly with the help of the auxiliary battery. The external power supply provides an uninterrupted power supply charging function. When the operating vehicle needs to stay outside for a long time, connect the external power supply when the car is stopped and the flame is turned off. The electrical and equipment in the medical room can still work.
After the production of each tank, CLW Group will conduct multiple treatments before painting to prevent cracking and skinning on the outside of the tank. First, the tank body and metal accessories are phosphated before coating, sprayed with polymer primer and metal topcoat. This can make the surface have strong adhesion, good corrosion resistance, bright and long-lasting color, and can withstand bad environments such as humidity, heavy sinking, and salt spray for a long time. Long-term use will not crack, peel, and fade.
